![]() ![]() ![]() The RE600 turned in a very respectable throughput score of 93.9Mbps on my 2.4GHz close-proximity (same room) test, besting the D-Link DAP-1650 (39.2Mbps) and the Netgear EX7000 (50.2Mbps) by a wide margin. Once you enter the router's password, you are good to go. The Spot Finder feature will show you what kind of signal strength you have between the extender and the router if it's not strong enough you'll have to relocate the extender to another outlet. This launches a setup wizard that will look for your network and ask you to connect to both bands. When the light turns solid green, you connect to the extender with your wireless device and enter in your browser's URL bar. You plug the extender into a three-pronged wall outlet somewhere between your router and a dead spot. Installation and Performance Installation is simple. The Status page displays Ethernet and wireless LAN statistics and network address (IP) information. The Administration page lets you back up and restore configuration settings, run diagnostics, change passwords, and view traffic logs. The Crossband page allows you to enable automatic band switching or you can manually turn Crossband on and off for each band. On the Basic page, you change the SSID for each band and assign a security protocol, and the Site survey page lets you view all available networks, as well as their frequency band, signal strength, and security protocol. ![]() The management interface is easy to use and offers a generous selection of settings, including Quality of Service (QoS) and Security (WEP, WPA, WPA2) settings. Crossband technology uses both bands (2.4GHz and 5GHz) to communicate with the router and automatically chooses the best available band in order to boost performance. Rather than sending a broad signal in all directions, Beamforming allows the extender to focus its signal directly at a client device to help improve performance. It operates on the 2.4GHz and 5GHz bands and features Beamforming and Crossband technologies. The RE6700 is an 802.11ac range extender with a maximum link rate of 867 Mbps. While it's nice to have a LAN port on a plug-in extender, it's even nicer when you get four or more of them, plus USB connectivity, like you do with the Netgear EX7000 and the D-Link Wi-Fi Dual Band Range Extender DAP-1650 ($47.30 at Walmart). An LED status indicator adorns the front, and a single Gigabit LAN port is located on the bottom of the device, along with an audio output for wirelessly streaming audio from your smartphone, laptop, or tablet. Two adjustable antennas are positioned on either side of the extender, and there are reset and Wireless Protected Setup (WPS) buttons on the right side. In fact, it offers a pass-through socket, which means you don't have to sacrifice an outlet at all. At 4.6 by 2.6 by 1.5 inches (HWD), it's slightly bigger than the D-Link DAP-1350 (3.6 by 2.2 by 1.3 inches), but its bulk doesn't prevent access to the adjacent socket on your wall outlet. For $50 more, the Netgear Nighthawk AC1900 Wi-Fi Range Extender (EX7000) ($139.97 at Amazon), our Editors' Choice, offers much better performance and connectivity options.ĭesign and Features The RE6700 is a plug-in extender designed for three-prong wall outlets. The RE6700 ($99.99 at Dell) is a snap to install and delivers good throughput up to 25 feet, but beyond that, it struggles, and it only has one wired LAN port. With the Linksys RE6700 AC1200 Amplify Dual Band Wi-Fi Range Extender ($119.99), you can bring wireless connectivity to those dead spots without having to replace or reconfigure your router. No matter how powerful your Wi-Fi router is, there's a good chance that you have dead spots in your home that it can't reach. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |